Accessories for correct installation
Accessories for correct installation

IS4SBLOCKN

NEW_EMPTY

39.34 + VAT

PCS PER PACK2

In stock

In stock

Unlocking tool for photovoltaic connectors Cabur line 4

Additional information

Code
Type
HS code
Colour
Material
Flame class
Operating temperature range
Protection degree
Quantity / Package

NOTES

To ensure the guarantee’s effectiveness, the use of Cabur Solar tools, in conformance with the standards and instructions found in Cabur official documentation, is an essential requirement

For further information see PDF catalog

HM598GR
spring clamp terminal block with 1 diode 1N4007, 2.5 mm²,...
CABUR PM100
PM404
Pre-assembled cross connection PM, 4 poles, suitable for CBD.4, SCB.4
CABUR PM100
PM254
Pre-assembled cross connection PM, 4 poles, suitable for CBR.2
Cabur SF900 SCREW TERMINAL BLOCKS SFR - CBF SERIES 1 LEVEL FUSE-HOLDER
SF904
terminal block with diode, 4 mm², beige
SB205R
Screw and sleeve, suitable for SCB.6
PHP0302B
Cross connection PHP, 2 poles, white, suitable for BPL.4
PHP0302
Cross connection PHP, 2 poles, yellow, suitable for BPL.4
PHP02B
Cross connection PHP, 2 poles, white, suitable for BPL/R
PHP02
Cross connection PHP, 2 poles, yellow, suitable for BPL/R
VP303
Flange for securing female connectors, colour grey, suitable for VPC.2...

HOW TO STRIP WIRE USING IS31579002

  1. The wire stripper works like a guillotine, suitable for wires of various thicknesses, allowing for fast and safe stripping.
  2. It acts simultaneously on both the sleeves of the photovoltaic wire, cutting them precisely.
  3. The blades move parallel to the wire, expelling the sheared off sleeve.

 

STRIPPING WITH IS3170

This wire stripper is able to strip wires with sections of 2.5, 4, 6 and 10 mm2. It is fitted with an end stop and allows for a stripped constant length of approx. 8 mm, compliant with the requirements of our PINS. The blade can be replaced.

  • To strip wires with a 2.5 mm2 section, the blade must make a complete turn around the external perimeter of the wire.
  • To strip wires with a 4 mm2 section, the blade must make two complete turns around the external perimeter of the wire.
  • To strip wires with a 6 mm2 section, the blade must make three complete turns around the external perimeter of the wire.

In order to preserve the number of strands, the blade should not be turned more times than those indicated in the recommendations above for each wire section.

 

HOW TO CHANGE THE UMCT CRIMPER MATRIX

  • Open the pliers as wide as possible (fig. 1);
  • slowly bring the two levers of the pliers together, until the locking/release mechanism makes three clicks (fig. 2);
  • observe the anchorage pin on the matrix (fig. 2);
  • insert the matrix, moving the anchorage pin towards the internal part of the pliers chamber (fig.3);
  • make sure that the plastic tooth has locked the matrix in place or that it has risen (fig.4);
  • press the two levers of the pliers, closing them as tightly as possible (fig.4);
  • release the handles; the pliers should open automatically and completely (fig.5);
  • if, when the pliers are closing, you realise that thecrimping is not successful or the crimp tool is blocked for any reason, it can be released by pressing and releasing the handles a few times and simultaneously pressing with your thumb on the release lever on the
    internal part of the handle (fig.6).

IN THE SAME CATEGORY

ISCRIVITI ALLA NEWSLETTER

Name(Required)
Email(Required)
Address(Required)
Privacy(Required)
The consent to the subscription to the Cabur Newsletter can be revoked, at any time, using the unsubscribe procedure available on the emails sent. PRIVACY POLICY

CABUR CUSTOMER CARE

for technical support
+39 019 58999.219  customercare@cabur.it
for commercial support
+39 019 58999.609 vendite@cabur.it

from monday to friday 8:30-12:30 13:00-17:00