€470.00 + VAT
Currently not available for online purchase. Contact our sales department.
Currently not available for online purchase. Contact our sales department.
Signal converter ModbusRTU / Modbus TCP
| Series | BRI |
|---|---|
| Code | XBRIRS485CP |
| Type | BRI-RS485-CP – |
| HS code | 8517620000, 8517620000 |
| TECHNICAL DATA | |
| Serial ports | 1 RS485 |
| Network interfaces | |
| Protocol | conversion from ModbusRTU/ to Modbus TCP |
| Speed | up to 1Mbit/s |
| MODBUS TECHNICAL DATA | |
| Speed distance | 0.6Km @ 38,4Kbps 0,9Km @ 19,2Kbps 1,2Km @ 9,6Kbps 2Km @ 4,8Kbps 3Km @ 2,4Kbps 7Km |
| Impedance of RS485 line | 120Ω |
| Max number of connectable devices in RS485 | 32 |
| GENERAL TECHNICAL DATA | |
| Power supply voltage | 8…30 Vdc |
| Current consumption | ≈ 41mA |
| Baud rate | 1200÷230400 bps (programmable) |
| Parity | None,Odd, Even, Mark, Space |
| Operating temperature range | ―20…+70°C |
| Insulation | 1.5 kVac /60s |
| Insulation type | 3-way |
| EMC Standard | EN 61000―2, EN 61000―4 |
| Overvoltage category / pollution degree | III/2 |
| Protection degree | IP20 |
| Connection terminal RS485 | 2.5 mm² |
| Connection terminal Ethernet | Shielded RJ45 connector |
| Housing material | Blend PC/ABS self―extinguishing |
| Dimensions (LxHxD) | 23x79x101 |
| Approximate weight | 100 g |
| APPROVALS AND MARKINGS | 
|
| Mounting information | on a rail, side by side |
| ACCESSORIES | |
| Mounting rail (IEC60715/TH35-7.5) | PR/3/AC, PR/3/AC/ZB, PR/3/AS, PR/3/AS/ZB |
For further information see PDF catalog
Modbus-RTU programmable analog converters
There are different models:
Each device has up to four independent channels, it is remotely configurable through the ModBus interface and in alternative with a uUSB port with no need for additional power supply.
The devices are fully programmable by means of CaburLab software application or directly accessing the ModBus registers by means of a PLC.
The XCIO4RLYMB can be configured to have a default safe condition called safestate that allows to set the state of the output when the power is off and/or when the device is remotely controlled.
Communication bridges
The XBRIRS485CP is a gateway which allows the connection between RS-485 interconnected devices towards a ModBus-TCP over Ethernet network .
The XBRIRS485ET and XBRIRS485WI are bridges with the capability to connect RS-485 devices to a 10/100 Base T Ethernet network based upon TCP/IP.
The Ethernet – RS485 communication passe through a virtual communication interface. The bridges parameters can be configu-red through a dedicate telnet interface (IP address, subnet mask, etc.).
Ethernet Switches
The XSWET5UP and XSWET5UP series of Din-rail Entry-level Unmanaged Ethernet Switches for industrial applications are highly compacted 5 and 8-port Ethernet switches that support IEEE 802.3/802.3u/802.3x with 10/100M, full/half-duplex, RJ45 ports.
The XSWET5UP and XSWET5UP switches are rated to operate at temperatures ranging from -10 to 60°C. The switches can be easily installed on a DIN-rail as well as multi-directional panel mounting.
Copyright © Cabur srl Sede legale Località isola Grande, 45 – 17041 Altare (SV) – Italia – Tel. 019-589991 – Fax 019-58999233 – E-mail: info@cabur.it
Cap. Sociale: €2.000.000 Int. versato – Reg. Soc. Trib. Savona N° 4635 – C.C.I.A.A. N° 27269- Export N° SV 000532 – P.IVA e Cod. Fisc.: 00100760099
DISCLAIMER Cabur Srl may change and update any document available online without any obligation to inform users. Only cabur.it and cabur.eu domains are registered and maintained by Cabur srl. Cabur has no responsibility for contents published on sites under the same name, with different extensions from .it and .eu
for technical and commercial support
from monday to friday 8:30-12:30 13:00-17:00
+39 019 58999.219 customercare@cabur.it
